MR. JO Artcast – CC33i
₹590.00 – ₹25,608.00 Inclusive of all taxes
BA & Nonyl Phenol free 3:1 resin system for deep crystal clear cast up to 30mm.
- Description
- Properties
- Applications
- How To Use
- Technical Data Sheet(TDS)
- FAQs
Description
Mr. JO Artcast – CC33i is a clear epoxy resin that you can pour deep. First, it works well for tabletops and art projects. Then, you mix it in a 3:1 ratio. Also, it flows smoothly and covers evenly. Because it is safe and free from harmful chemicals, it is good for the environment. Finally, it creates strong and shiny surfaces. Both experts and beginners trust this resin.
- Color: Clear
- Pot life @25°C: 280-380 mins
- Mixing Ratio: 3:1 PBW
- Mixture consistency: Low viscosity liquid
- Optics: Transparent
- Casting up to 30mm
- Table top
- Artifacts
- Substrate surfaces should be freed from laitance and dust by sand-blasting. In case sand-blasting is not possible, thorough abrading with a hard wire brush should be preferable.
- Use Part A & Part B in ratio 3:1 pbw. Mix the two components in small batches thoroughly for at least 2minutes. Apply the mix directly or using proper spatula to the pretreated surfaces.
- The mixture should be applied as soon as the homogenous mix is achieved.
- Allow the material to cure for at least 24 hours before putting to use.
A1. These are clear epoxy casting resins used for:
- River tables & epoxy wood tables
- 3D artifacts, sculptures, decorative blocks
- Jewelry, coasters, crafts, and cast décor items
A2.
Product | Key Traits | Pot Life | Ideal For |
---|---|---|---|
Flagship, long pot life, thick pour | Long (60–90 min) | Large table pours, deep molds, bulk casting | |
CC33i | Fast cure, high hardness | Short (~25–30 min) | Jewelry, molds, small/thin castings |
FS33 | Bis-A free, Bis-F based resin | Moderate (~40–60 min) |
Applications avoiding Bis-A due to compliance or safety concerns |
A3. Yes — all are low odor, VOC-free, and suitable for use in well-ventilated craft or studio environments.
Q4. Why would someone choose MR. JO Artcast-FS33 over the others?A4. FS33 is based on Bisphenol-F epoxy, making it free from Bisphenol-A. It’s ideal for:
- Export projects requiring Bis-A–free formulations
- Health-conscious markets
- Crafts and giftware with consumer safety considerations
Q5. What is the mixing ratio for all three?
A5. All three systems are mixed at 3:1 by weight (Resin : Hardener). Mix thoroughly and slowly to avoid air entrapment.
Q6. How thick can I pour with each product?A6.
- CC33: Up to 2–3 inches (50–75 mm) in one go
- CC33i: Best for up to 10–15 mm at a time
- FS33: Suitable for 10–25 mm, depending on mold and ambient temperature
A7. Yes — MR. JO Artcast-CC33 is the preferred choice for large-format and river tables due to its low exotherm and long work time.
Q8. How long do these systems take to cure? A8.- CC33: Touch dry ~24 hrs, full cure ~72 hrs
- CC33i: Touch dry ~6–8 hrs, full cure ~24 hrs
- FS33: Touch dry ~12–16 hrs, full cure ~48 hrs Curing speed depends on casting size, temperature, and humidity.
A9. Yes — use MR. JO ArtPigments or other compatible epoxy-safe pigment pastes or powders. Use up to 4–6% max for best results.
Q10. Will the cast yellow over time?A10. All products are formulated with anti-yellowing agents, but long-term UV exposure may still cause some yellowing. Use indoors or apply a UV-resistant topcoat if needed.
Q11. How do I remove bubbles from the mix?A11.
- Mix slowly
- Allow the resin to sit for 2–3 minutes
- Use a heat gun or flame torch gently over the surface to remove surface bubbles
A12. Yes — all systems can be sanded and polished after full cure to get a glass-like finish.
Q13. Are these resins food safe?A13. These are not certified food-grade. If intended for surfaces with food contact, use a food-safe topcoat over the cured resin.
Q14. What if I need to pour in layers?A14. You can pour in layers:
- Let the first layer gel or partially cure (~8–12 hrs)
- Lightly sand if fully cured
- Pour the next layer to ensure bonding
A15. 12 months in original sealed containers when stored in a cool, dry place (15–25°C).