Product - MR. Floorkot – CMR

Description

Mr. Floorkot – CMR is a two-part epoxy floor coating. It has a medium thickness and contains no solvents. It protects against oils, chemicals, acids, and salty water.

• Color: Pigmented
• Pot life @25°C: 20-40 mins
• Mixing Ratio: 100:20 PBW
• Good Chemical resistant
• Mixture consistency: Flowable liquid
• Coverage: 4 m²/kg/coat
• Optics: Opaque

• Area prone to chemical spillage
• Laboratory
• Industrial floors
• Area prone to oil spillage

• Surfaces should be freed from laitance and dust by sand-blasting. In case sand blasting is not possible, thorough abrading with a hard wire brush should be preferable.
• Suitable degreasing agent should be used to remove any grease, oil or traces on the surface.

• Repair the surface if damaged. Allow 2-3 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Adhesives for repairing.
• Apply primer for better adhesion on substrate. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Primers.
• Mix all the two components provided in kit thoroughly for at least 2minutes. Apply the mix directly by pouring and spreading with the help of trowel.
• Allow 5-6 hour for surface to dry and 24 hours to achieve full strength coating.

A1. MR. JO Floorkot – CMR is a two-component, solvent-free epoxy floor coating designed for:

• Industrial floors requiring chemical resistance
• Zones exposed to cleaning agents, oils, alkalis, and mild acids
• Areas where regular epoxy coatings like MR. JO Floorkot-HB may not suffice

A2. While both are high-performance coatings:

• CMR offers superior chemical resistance
• Slightly more durable in harsher environments
• Recommended for chemical plants, labs, and process areas

A3. The system is mixed at 100:20 by weight (Resin : Hardener). Mix well to ensure uniform performance and curing.

A4. It dries to a smooth, glossy finish and is usually offered in grey or other industrial tones. Custom colors may be possible for volume orders.

A5. No, CMR is a brush/roller-applied coating, not a self-leveling floor system.

A6.

• Clean the surface of oil, dust, and loose particles
• For concrete: mechanically grind or shot-blast
• Prime with Mr. JO Primer-MVC, LVC, or UPS depending on substrate condition

A7.

• Apply using a roller or brush
• Typical application: 2 coats for full coverage and performance
• Maintain a minimum of 8–12 hours between coats

A8. Approximately 4–5 m²/kg/coat, depending on substrate condition and desired film thickness.

A9.

• Pot life: 30–40 minutes at 25°C
• Touch dry: 6–8 hours
• Light traffic: 24 hours
• Full cure & chemical resistance: 5–7 days

A10. Yes — it can be used over epoxy screeds, self-leveling epoxy floors, or other compatible primers/coatings to improve surface durability and chemical resistance.

A11. Yes — CMR is designed to withstand frequent cleaning cycles and mild-to-moderate chemical exposure, including industrial cleaners and spills.

A12. Like most epoxies, some discoloration may occur under UV light. For outdoor or sun-exposed areas, a UV-stable topcoat is recommended.

A13. The finish is smooth by default. For anti-skid applications, you may:

• Broadcast silica/quartz sand between coats
• Use a non-slip top layer if required

A14. Yes — it can be applied on vertical concrete or metal surfaces with a brush or roller, though thinner coats may be required to prevent sagging.

A15. Yes — sand the surface lightly, clean, and reapply CMR or a compatible topcoat.