Product - MR. JO Floorkot – AS

Description

Mr. JO Floorkot – AS is a two-part, solvent-free epoxy coating. It has a medium viscosity and high build. Moreover, it ensures electrostatic dissipation. Its conductive resistance reaches up to 10⁹ Ohms. Also, this strong coating protects floors in Workshops and stores. It creates a smooth, even surface. As a result, it lasts long. It also improves safety and reliability.

• Color: Pigmented
• Pot life @25°C: 25-45 mins
• Mixing Ratio: 100:20 PBW
• Electrostatic dissipating properties
• Mixture consistency: Flowable liquid
• Coverage: 4 m²/kg/coat
• Optics: Opaque

• Data center
• Semiconductor fabrication industry
• Military & aerospace industries
• Antistatic coating

• Surfaces should be freed from laitance and dust by sand-blasting. In case sandblasting is not possible, thorough abrading with a hard wire brush should be preferable.
• Suitable degreasing agent should be used to remove any grease, oil or traces on the surface.

• Repair the surface if damaged. Allow 2-3 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Adhesives for repairing.
• Apply primer for better adhesion on substrate. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Primers.
• Mix all the two components provided in kit thoroughly for at least 2minutes. Apply the mix directly by pouring and spreading with the help of trowel.
• Allow 5-6 hour for surface to dry and 24 hours to achieve full strength coating.

A1. MR. JO Floorkot – AS is a conductive antistatic epoxy floor coating used in environments where electrostatic discharge (ESD) needs to be prevented. Ideal for:

• Electronics and semiconductor assembly areas
• Pharmaceutical facilities
• Explosive or flammable material zones
• Data centers, server rooms, and cleanrooms

A2. While both are solvent-free epoxy floor coatings, MR. JO Floorkot – AS includes conductive properties to safely dissipate static electricity, while HB is a standard protective coating.

A3. No. It must be applied over MR. JO Primer – AS, which provides the conductive grounding base. Together, they form a complete ESD flooring system.

A4. It typically comes in black or dark grey to complement the conductive primer and highlight clean area zones.

A5. Recommended for:

• Electronics manufacturing units
• Control rooms and laboratories
• Paint and chemical handling zones
• Battery and capacitor storage areas

A6. Refer to the label. Typical mix ratio is 2-component, with pot life ~30–40 minutes at 25°C.

A7.

• Short-pile rollers or squeegees
• ESD-compliant footwear and accessories (for large-scale work)
• Copper tape or grounding wires (if required by your ESD system design)

A8.

• 1 coat of MR. JO Primer-AS
• 1–2 coats of MR. JO Floorkot – AS depending on desired build and conductivity

A9.

• Touch dry: 6–8 hours
• Recoat: 12–24 hours
• Full cure: 5–7 days (depending on ambient conditions)

A10. Grounding is achieved via copper tape or grounding rods laid into the conductive primer. The coating transfers static charges to the grounded system.

A11. Use surface resistance meters or point-to-point/point-to-ground resistance tests after 7 days of curing.

A12. Yes, but use mild, non-abrasive cleaners. Avoid strong solvents that may affect conductivity.

A13. Yes. Avoid applying waxes, polishes, or sealers unless ESD-safe variants are used. These can insulate the surface and reduce performance.

A14. Not recommended unless it’s an ESD-safe clear coat. Standard clear coats will block static dissipation.

A15. With proper maintenance and cleaning, the system will remain effective for 5+ years. Conductivity should be tested periodically in critical zones.