mr. jo Ask Mr. Jo Trouble finding a suitable product?New

Our Products

MR. JO Floor-SL0.5

Packaging: 13.5 KG Packaging: 13.5 KG

System Properties

  • Color: Neutral | Factory Pigmented
  • Pot life @25°C: 20-40 mins
  • Mixing Ratio: 100:50:120 PBW
  • Good mechanical properties
  • Mixture consistency: Self levelling
  • Thickness 0.5mm
  • Coverage: 0.8 kg/m2

Applications

  • Garage
  • Mechanical workshops
  • Warehouses
  • Parking area
Download TDS

How to use

  • The mixture should be applied on a clean and rough surface. For good results, it is required that the substrate is free from loose particles. Suitable degreasing agent should be used to remove any grease, oil or traces on the surface.

  • Repair the surface if damaged. Allow 2-3 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Adhesives for repairing.


  • Apply primer for better adhesion on substrate. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Primers.

  • An underlay is suggested if the substrate is badly damaged or is prone to high level of mechanical abrasion. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Underlays.

  • Mix all the three components provided in kit thoroughly for at least 2minutes. Copper mesh is laid and then mix directly poured and spread with the help of trowel.

  • Allow 5-6 hours for surface to dry and 24 hours to achieve full strength.

 

MR. JO Floor-CRSL0.5

Packaging: 13.5 KG

Packaging: 13.5 KG Packaging: 13.5 KG

System Properties

  • Color: Neutral | Factory Pigmented
  • Pot life @25°C: 20-40 mins
  • Mixing Ratio: 100:50:120 PBW
  • Self levelling
  • Thickness: 0.5mm
  • Coverage: 0.8 kg/m2

Applications

  • Area prone to chemical spillage
  • Laboratory
  • Industrial floors
  • Area prone to oil spillage
Download TDS

How to use

  • The mixture should be applied on a clean and rough surface. For good results, it is required that the substrate is free from loose particles. Suitable degreasing agent should be used to remove any grease, oil or traces on the surface.

  • Repair the surface if damaged. Allow 2-3 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Adhesives for repairing.


  • Apply primer for better adhesion on substrate. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Primers.

  • An underlay is suggested if the substrate is badly damaged or is prone to high level of mechanical abrasion. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Underlays.

  • Mix all the three components provided in kit thoroughly for at least 2minutes. Copper mesh is laid and then mix directly poured and spread with the help of trowel.

  • Allow 5-6 hours for surface to dry and 24 hours to achieve full strength.

MR. JO Floor-SL1

Packaging: 15 KG

Packaging: 15 KG Packaging: 15 KG

System Properties

  • Color: Neutral | Factory Pigmented
  • Pot life @25°C: 20-40 mins
  • Mixing Ratio: 100:50:150 PBW
  • Good mechanical properties
  • Mixture consistency: Self levelling
  • Thickness: 1 mm
  • Coverage: 1.6 kg/m2

Applications

  • Garage
  • Mechanical workshops
  • Warehouses
  • Parking area
Download TDS

How to use

  • The mixture should be applied on a clean and rough surface. For good results, it is required that the substrate is free from loose particles. Suitable degreasing agent should be used to remove any grease, oil or traces on the surface.

  • Repair the surface if damaged. Allow 2-3 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Adhesives for repairing.


  • Apply primer for better adhesion on substrate. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Primers.

  • An underlay is suggested if the substrate is badly damaged or is prone to high level of mechanical abrasion. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Underlays.

  • Mix all the three components provided in kit thoroughly for at least 2minutes. Copper mesh is laid and then mix directly poured and spread with the help of trowel.

  • Allow 5-6 hours for surface to dry and 24 hours to achieve full strength.

 

MR. JO Floor-CRSL1

Packaging: 15 KG

Packaging: 15 KG Packaging: 15 KG

System Properties

  • Color: Neutral | Factory Pigmented
  • Pot life @25°C: 20-40 mins
  • Mixing Ratio: 100:50:150 PBW
  • Good Chemical resistant
  • Mixture consistency: Self levelling
  • Thickness: 1 mm
  • Coverage: 1.6 kg/m2

Applications

  • Area prone to chemical spillage
  • Laboratory
  • Industrial floors
  • Area prone to oil spillage
Download TDS

How to use

  • The mixture should be applied on a clean and rough surface. For good results, it is required that the substrate is free from loose particles. Suitable degreasing agent should be used to remove any grease, oil or traces on the surface.

  • Repair the surface if damaged. Allow 2-3 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Adhesives for repairing.


  • Apply primer for better adhesion on substrate. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Primers.

  • An underlay is suggested if the substrate is badly damaged or is prone to high level of mechanical abrasion. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Underlays.

  • Mix all the three components provided in kit thoroughly for at least 2minutes. Copper mesh is laid and then mix directly poured and spread with the help of trowel.

  • Allow 5-6 hours for surface to dry and 24 hours to achieve full strength.

 

MR. JO Floor-SL2

Packaging: 16.5 KG

Packaging: 16.5 KG Packaging: 16.5 KG

System Properties

  • Color: Neutral | Factory Pigmented
  • Pot life @25°C: 20-40 mins
  • Mixing Ratio: 100:50:180 PBW
  • Good mechanical properties
  • Mixture consistency: Self levelling
  • Thickness: 2 mm
  • Coverage: 3.2 kg/m2

Applications

  • Garage
  • Mechanical workshops
  • Warehouses
  • Parking area
Download TDS

How to use

  • The mixture should be applied on a clean and rough surface. For good results, it is required that the substrate is free from loose particles. Suitable degreasing agent should be used to remove any grease, oil or traces on the surface.

  • Repair the surface if damaged. Allow 2-3 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Adhesives for repairing.


  • Apply primer for better adhesion on substrate. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Primers.

  • An underlay is suggested if the substrate is badly damaged or is prone to high level of mechanical abrasion. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Underlays.

  • Mix all the three components provided in kit thoroughly for at least 2minutes. Copper mesh is laid and then mix directly poured and spread with the help of trowel.

  • Allow 5-6 hours for surface to dry and 24 hours to achieve full strength.

 

MR. JO Floor-CRSL2

Packaging: 16.5 KG

Packaging: 16.5 KG Packaging: 16.5 KG

System Properties

  • Color: Neutral | Factory Pigmented
  • Pot life @25°C: 20-40 mins
  • Mixing Ratio: 100:50:180 PBW
  • Good Chemical resistant
  • Mixture consistency: Self levelling
  • Thickness: 2 mm
  • Coverage: 3.2 kg/m2

Applications

  • Area prone to chemical spillage
  • Laboratory
  • Industrial floors
  • Area prone to oil spillage
Download TDS

How to use

  • The mixture should be applied on a clean and rough surface. For good results, it is required that the substrate is free from loose particles. Suitable degreasing agent should be used to remove any grease, oil or traces on the surface.

  • Repair the surface if damaged. Allow 2-3 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Adhesives for repairing.


  • Apply primer for better adhesion on substrate. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Primers.

  • An underlay is suggested if the substrate is badly damaged or is prone to high level of mechanical abrasion. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Underlays.

  • Mix all the three components provided in kit thoroughly for at least 2minutes. Copper mesh is laid and then mix directly poured and spread with the help of trowel.

  • Allow 5-6 hours for surface to dry and 24 hours to achieve full strength.

 

MR. JO Floor-ASL1

Packaging: 11.25 KG

Packaging: 11.25 KG Packaging: 11.25 KG

System Properties

  • Color: Pigmented
  • Pot life @25°C: 20-40 mins
  • Mixing Ratio: 100:50:75 PBW
  • Electrostatic dissipating properties
  • Mixture consistency: Self levelling
  • Mixture consistency: Self levelling
  • Thickness: 1 mm
  • Coverage: 1.6 kg/m2

Applications

  • Data center
  • Semiconductor fabrication industry
  • Military & aerospace industries
  • Antistatic flooring
Download TDS

How to use

  • The mixture should be applied on a clean and rough surface. For good results, it is required that the substrate is free from loose particles. Suitable degreasing agent should be used to remove any grease, oil or traces on the surface.

  • Repair the surface if damaged. Allow 2-3 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Adhesives for repairing.


  • Apply primer for better adhesion on substrate. Copper mesh is suggested to be laid before applying primer. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Primers. Rub the surface with sand paper after each coat for better charge dissipation.

  • Mix all the three components provided in kit thoroughly for at least 2minutes. Mixture is then directly poured and spread with the help of trowel.

  • Allow 5-6 hour for surface to dry and 24 hours to achieve full strength flooring.

 

MR. JO Floor-ASL2

Packaging: 11.25 KG

Packaging: 12.5 KG Packaging: 12.5 KG

System Properties

  • Color: Pigmented
  • Pot life @25°C: 20-40 mins
  • Mixing Ratio: 100:50:100 PBW
  • Electrostatic dissipating properties
  • Mixture consistency: Self levelling
  • Thickness: 2mm
  • Coverage: 3.2 kg/m2

Applications

  • Data center
  • Semiconductor fabrication industry
  • Military & aerospace industries
  • Antistatic flooring
Download TDS

How to use

  • The mixture should be applied on a clean and rough surface. For good results, it is required that the substrate is free from loose particles. Suitable degreasing agent should be used to remove any grease, oil or traces on the surface.

  • Repair the surface if damaged. Allow 2-3 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Adhesives for repairing.


  • Apply primer for better adhesion on substrate. Copper mesh is suggested to be laid before applying primer. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Primers. Rub the surface with sand paper after each coat for better charge dissipation.

  • Mix all the three components provided in kit thoroughly for at least 2minutes. Mixture is then directly poured and spread with the help of trowel.

  • Allow 5-6 hour for surface to dry and 24 hours to achieve full strength flooring.

MR. JO Floorkot-HB

Packaging: 6 KG

Packaging: 6 KG Packaging: 6 KG

System Properties

  • Color: Pigmented
  • Pot life @25°C: 20-40 mins
  • Mixing Ratio: 100:20 PBW
  • Good mechanical properties
  • Mixture consistency: Flowable liquid
  • Coverage: 4 m2/kg/coat
  • Optics: Opaque

Applications

  • Food courts
  • Restaurant
  • Parking lot
Download TDS

How to use

  • Remove all dust and debris by physical and mechanical means, prior
    to application of the product. surfaces should be freed from
    laitance and dust by sand-blasting. In case sand-blasting is not
    possible, thorough abrading with a hard wire brush should be
    preferable.

  • Repair the surface if damaged. Allow 2-3 hours for surface of
    repaired area to dry. Choose a suitable product from Jpoxy’s JO
    range of
    Adhesives for
    repairing.

  • Apply primer for better adhesion on substrate. Allow 4-5 hours for
    surface of repaired area to dry. Choose a suitable product from
    Jpoxy’s JO range of
    Primers.

  • Mix the two components provided in kit thoroughly for at least 2minutes.
    Apply the mix directly by pouring and spreading with the help of trowel.

  • Allow 5-6 hour for surface to dry and 24 hours to achieve full strength
    coating.

MR. JO Floorkot-CMR

Packaging: 6 KG Packaging: 6 KG

System Properties

  • Color: Pigmented
  • Pot life @25°C: 20-40 mins
  • Mixing Ratio: 100:20 PBW
  • Good Chemical resistant
  • Mixture consistency: Flowable liquid
  • Coverage: 4 m2/kg/coat
  • Optics: Opaque

Applications

  • Area prone to chemical spillage
  • Laboratory
  • Industrial floors
  • Area prone to oil spillage
Download TDS

How to use

  • Remove all dust and debris by physical and mechanical means, prior to
    application of the product. surfaces should be freed from laitance and
    dust by sand-blasting. In case sand-blasting is not possible, thorough
    abrading with a hard wire brush should be preferable.

  • Repair the surface if damaged. Allow 2-3 hours for surface of repaired
    area to dry. Choose a suitable product from Jpoxy’s JO range of
    Adhesives for
    repairing.

  • Apply primer for better adhesion on substrate. Allow 4-5 hours for
    surface of repaired area to dry. Choose a suitable product from Jpoxy’s
    JO range of
    Primers.

  • Mix the two components provided in kit thoroughly for at least 2minutes.
    Apply the mix directly by pouring and spreading with the help of trowel.

  • Allow 5-6 hour for surface to dry and 24 hours to achieve full strength
    coating.

MR. JO Floorkot-YLW

Packaging: 6 KG Packaging: 6 KG

System Properties

  • Color: Yellow
  • Pot life @25°C: 20-40 mins
  • Mixing Ratio: 100:20 PBW
  • Good mechanical properties
  • Mixture consistency: Brush able liquid
  • Coverage: 40 rmt/kg/coat for 3” wide
  • Optics: Opaque

Applications

  • Direction marking on concrete roads
  • Work area marking in manufacturing facilities
  • Vehicle parking area marking in parking lot
  • Vehicle parking area marking in garage
Download TDS

How to use

  • Remove all dust and debris by physical and mechanical means, prior to
    application of the product. surfaces should be freed from laitance and
    dust by sand-blasting. In case sand-blasting is not possible, thorough
    abrading with a hard wire brush should be preferable.

  • Repair the surface if damaged. Allow 2-3 hours for surface of repaired
    area to dry. Choose a suitable product from Jpoxy’s JO range of
    Adhesives for
    repairing.

  • Apply primer for better adhesion on substrate. Allow 4-5 hours for
    surface of repaired area to dry. Choose a suitable product from Jpoxy’s
    JO range of
    Primers.

  • Mix all the two components of flooring kit thoroughly for at least
    2minutes. Make marking with masking tape as per required width and apply
    the mix directly by brush or roller with in the marking.

  • Allow 5-6 hour for surface to dry and 24 hours to achieve full strength
    coating.

MR. JO Floorkot-CLR

Packaging: 7.5 KG Packaging: 7.5 KG

System Properties

  • Color: Clear
  • Pot life @25°C: 25-45 mins
  • Mixing Ratio: 100:50 PBW
  • High Clarity
  • Mixture consistency: Flowable liquid
  • Coverage: 4 m2/kg/coat
  • Optics: Transparent

Applications

  • Decorative clear coat
  • 3D floors
  • Protective coating
  • Area prone to oil spillage
Download TDS

How to use

  • Remove all dust and debris by physical and mechanical means, prior to
    application of the product. surfaces should be freed from laitance and
    dust by sand-blasting. In case sand-blasting is not possible, thorough
    abrading with a hard wire brush should be preferable.

  • Repair the surface if damaged. Allow 2-3 hours for surface of repaired
    area to dry. Choose a suitable product from Jpoxy’s JO range of
    Adhesives for
    repairing.

  • Apply primer for better adhesion on substrate. Allow 4-5 hours for
    surface of repaired area to dry. Choose a suitable product from Jpoxy’s
    JO range of
    Primers.

  • Mix all the two components provided in kit thoroughly for at least 2
    minutes. Apply the mix directly by pouring and spreading with the help
    of trowel.

  • Allow 5-6 hour for surface to dry and 24 hours to achieve full strength
    coating.

MR. JO Floorkot-AS

Packaging: 6 KG Packaging: 6 KG

System Properties

  • Color: Pigmented
  • Pot life @25°C: 25-45 mins
  • Mixing Ratio: 100:20 PBW
  • Electrostatic dissipating properties
  • Mixture consistency: Flowable liquid
  • Coverage: 4 m2/kg/coat
  • Optics: Opaque

Applications

  • Data center
  • Semiconductor fabrication industry
  • Military & aerospace industries
  • Antistatic coating
Download TDS

How to use

  • Remove all dust and debris by physical and mechanical means, prior to
    application of the product. surfaces should be freed from laitance and
    dust by sand-blasting. In case sand-blasting is not possible, thorough
    abrading with a hard wire brush should be preferable.

  • Repair the surface if damaged. Allow 2-3 hours for surface of repaired
    area to dry. Choose a suitable product from Jpoxy’s JO range of
    Adhesives for
    repairing.

  • Apply primer for better adhesion on substrate. Copper mesh is suggested
    to be laid before applying primer. Allow 4-5 hours for surface of
    repaired area to dry. Choose a suitable product from Jpoxy’s JO range of
    Primers. Rub the surface with sand paper after each coat for better
    charge dissipation

  • Mix the two components provided in kit thoroughly for at least
    2minutes. Apply the mix directly by pouring and spreading with the
    help of trowel.

  • Allow 5-6 hour for surface to dry and 24 hours to achieve full
    strength coating.

MR. JO Primer-MVC

Packaging: 7.5 KG Packaging: 7.5 KG

System Properties

  • Color: Pale yellow
  • Pot life @25°C: 120-150 mins
  • Mixing Ratio: 100:50 PBW
  • Mixture consistency: Medium viscosity liquid
  • Coverage: 4 m2/kg
  • Optics: : Transparent/Translucent

Applications

  • Substrate pore sealing
  • Adhesion promoter
  • Sealer coat
Download TDS

How to use

  • Surfaces should be freed from laitance and dust by sand-blasting. In case sand-blasting is not possible, thorough abrading with a hard wire brush should be preferable. Suitable degreasing agent should be used to remove any grease, oil or traces on the surface.
  • Mix the two components together thoroughly for at least 2 minutes so as to achieve uniform mixing and thorough consistency of the mix. Apply the mix using brush or spatula to the pretreated surfaces.
  • Allow 4-5 hours for surface to dry and 24 hours to achieve full strength.

MR. JO Primer-LVC

Packaging: 6 KG Packaging: 6 KG

System Properties

  • Color: Pale yellow
  • Pot life @25°C: 100-120 mins
  • Mixing Ratio: 100:50 PBW
  • Mixture consistency: Low viscosity liquid
  • Coverage: 4 m2/kg
  • Optics: Transparent/Translucent

Applications

  • Sealing minute pinholes
  • In between substrate & topcoat to enhance
  • adhesion
  • Structure strengthening
Download TDS

How to use

  • Surfaces should be freed from laitance and dust by sand-blasting. In
    case sand-blasting is not possible, thorough abrading with a hard wire
    brush should be preferable. Suitable degreasing agent should be used to
    remove any grease, oil or traces on the surface.

  • Mix the two components together thoroughly for at least 2 minutes so as
    to achieve uniform mixing and thorough consistency of the mix. Apply the
    mix using brush or spatula to the pretreated surfaces.

  • Allow 4-5 hours for surface to dry and 24 hours to achieve full
    strength.

MR. JO Primer-UPS

Packaging: 7.5 KG Packaging: 7.5 KG

System Properties

  • Color: Brownish
  • Pot life @25°C: 80-100 mins
  • Mixing Ratio: 100:50 PBW
  • Mixture consistency: Medium viscosity liquid
  • Damp, moist & underprepared substrate curing
  • Coverage: 4 m2/kg
  • Optics: Transparent/Translucent

Applications

  • Concrete strengthening
  • Adhesion promoter
  • Sealer coat
Download TDS

How to use

  • The mixture should be applied on a clean and rough surface. For good
    results, it is required that the substrate is free from loose particles.
    Suitable degreasing agent should be used to remove any grease, oil or
    traces on the surface.

  • Mix the two components in small batches thoroughly for at least
    2minutes. Apply the mix using brush or spatula to the pretreated
    surfaces.

  • Allow 4-5 hours for surface to dry and 24 hours to achieve full
    strength.

MR. JO Primer-AS

Packaging: 3.9 KG Packaging: 3.9 KG

System Properties

  • Color: Black
  • Pot life @25°C: 90-120 mins
  • Mixing Ratio: 100:30 PBW
  • Mixture consistency: Thixotropic paste
  • Electrostatic dissipating properties
  • Coverage: 4 m2/kg
  • Optics: Opaque

Applications

  • Data center
  • Semiconductor fabrication industry
  • Military & aerospace industries
  • Antistatic coating
Download TDS

How to use

  • Surfaces should be freed from laitance and dust by sand-blasting. In
    case sand-blasting is not possible, thorough abrading with a hard wire
    brush should be preferable. Suitable degreasing agent should be used to
    remove any grease, oil or traces on the surface.

  • Mix the two components together thoroughly for at least 2 minutes so as
    to achieve uniform mixing and thorough consistency of the mix. . Copper
    mesh is suggested to be laid before applying primer. Apply the mix using
    brush or spatula to the pretreated surfaces.

  • Allow 4-5 hours for surface to dry and 24 hours to achieve full
    strength. Rub the surface with sand paper after each coat for better
    charge dissipation.

MR. JO Underlay-TMP

Packaging: 40 KG Packaging: 40 KG

System Properties

  • Color: Neutral
  • Pot life @25°C: 120-150 mins
  • Mixing Ratio: 100:50:650 PBW
  • Mixture consistency: Tampable
  • Coverage: 1.8 kg/m2/mm

Applications

  • Flooring
  • Pavement
  • Slope for drainage
  • As a bedding to enhanced floor’s mechanical strength
Download TDS

How to use

  • Remove all dust and debris by physical and mechanical means, prior to
    application of the product. surfaces should be freed from laitance and
    dust by sand-blasting. In case sand-blasting is not possible, thorough
    abrading with a hard wire brush should be preferable.

  • Repair the surface if damaged. Allow 2-3 hours for surface of repaired
    area to dry. Choose a suitable product from Jpoxy’s JO range of
    Adhesives for
    repairing.

  • Apply primer for better adhesion on substrate. Allow 4-5 hours for
    surface of repaired area to dry. Choose a suitable product from Jpoxy’s
    JO range of
    Primers.

  • Mix all the three components provided in kit thoroughly for at least
    2minutes. Apply the mix directly by pouring and spreading with the help
    of trowel.

  • Allow 4-5 hour for surface to dry and 24 hours to achieve full strength
    flooring.

MR. JO Underlay-FLO

Packaging: 20 KG Packaging: 20 KG

System Properties

  • Color: Neutral
  • Pot life @25°C: 100-120 mins
  • Mixing Ratio: 100:50:250 PBW
  • Mixture consistency: Flowable
  • Coverage: 1.8 kg/m2/mm

Applications

  • Flooring
  • Pavement
  • Slope for drainage
  • As a bedding to enhanced floor’s mechanical strength
Download TDS

How to use

  • Remove all dust and debris by physical and mechanical means, prior to
    application of the product. surfaces should be freed from laitance and
    dust by sand-blasting. In case sand-blasting is not possible, thorough
    abrading with a hard wire brush should be preferable.

  • Repair the surface if damaged. Allow 2-3 hours for surface of repaired
    area to dry. Choose a suitable product from Jpoxy’s JO range of
    Adhesives for
    repairing.

  • Apply primer for better adhesion on substrate. Allow 4-5 hours for
    surface of repaired area to dry. Choose a suitable product from Jpoxy’s
    JO range of
    Primers.

  • Mix all the three components provided in kit thoroughly for at least
    2minutes. Apply the mix directly by pouring and spreading with the help
    of trowel.

  • Allow 4-5 hour for surface to dry and 24 hours to achieve full strength
    flooring.

MR. JO Underlay-CMR

Packaging: 32.4 KG Packaging: 32.4 KG

System Properties

  • Color: Neutral
  • Pot life @25°C: 80-100 mins
  • Mixing Ratio: 100:60:650 PBW
  • Mixture consistency: Tampable
  • Good chemical resistant
  • Coverage: 1.8 kg/m2/mm

Applications

  • Industrial flooring
  • Pavement
  • Slope for drainage
  • As a bedding to enhanced floor’s mechanical strength
Download TDS

How to use

  • Remove all dust and debris by physical and mechanical means, prior to
    application of the product. surfaces should be freed from laitance and
    dust by sand-blasting. In case sand-blasting is not possible, thorough
    abrading with a hard wire brush should be preferable.

  • Repair the surface if damaged. Allow 2-3 hours for surface of repaired
    area to dry. Choose a suitable product from Jpoxy’s JO range of
    Adhesives for
    repairing.

  • Apply primer for better adhesion on substrate. Allow 4-5 hours for
    surface of repaired area to dry. Choose a suitable product from Jpoxy’s
    JO range of
    Primers.

  • Mix all the three components provided in kit thoroughly for at least
    2minutes. Apply the mix directly by pouring and spreading with the help
    of trowel.

  • Allow 4-5 hour for surface to dry and 24 hours to achieve full strength
    flooring.

Get in touch

    Are you trader? Yes