Ask Mr. Jo
Our Products
MR. JO Protectokot- BLK
Packaging: 2 KG
Packaging: 5 KG
Packaging: 10 KG
System Properties
- Color: Black
- Pot life @25°C: 25-35mins
- Mixing Ratio: 100:100 PBW
- Mixture consistency: Brush able liquid
- Excellent saline water resistant
- Coverage : 4 m2/kg/coat
- Optics : Opaque
Applications
- ETP plants
- Tank inner lining
- Waterproofing
- Corrosion protection
How to use
-
The mixture should be applied on a clean and rough surface. For good results, it is required that the substrate is free from loose particles. Suitable degreasing agent should be used to remove any grease, oil or traces on the surface.
-
Repair the surface if damaged. Allow 2-3 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Adhesives for repairing.
-
Apply primer for better adhesion on substrate. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Primers.
-
Mix the two components in small batches thoroughly for at least 2minutes. Apply the mix using brush or spatula to the pretreated surfaces.
-
Allow 4-5 hours for surface to dry and 24 hours to achieve full strength.
MR. JO Protectokot- CR
Packaging: 6.4 KG
System Properties
- Color: Brownish yellow
- Pot life @25°C: 90-120 mins
- Mixing Ratio: 100:60 PBW
- Good Chemical resistant
- Mixture consistency: Flowable liquid
- Coverage: 4 m2/kg/coat
- Optics : Transparent/Translucent
Applications
- Anti corrosive coating
- Industrial equipment
- Area prone to chemical spillage
How to use
-
Surfaces should be freed from laitance and dust by sand-blasting. In case sand-blasting is not possible, thorough abrading with a hard wire brush should be preferable. Suitable degreasing agent should be used to remove any grease, oil or traces on the surface.
-
Repair the surface if damaged. Allow 2-3 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Adhesives for repairing.
-
Apply primer for better adhesion on substrate. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Primers.
-
Mix the two components together thoroughly for at least 2 minutes so as to achieve uniform mixing and thorough consistency of the mix. Apply the mix using brush or spatula to the pretreated surfaces.
-
Allow 4-5 hours for surface to dry and 24 hours to achieve full strength.
MR. JO Protectokot- HBCR
Packaging: 5.7 KG
System Properties
- Color: Green
- Pot life @25°C: 20-30 mins
- Mixing Ratio: 100:14 PBW
- High build with chemical resistant
- Mixture consistency: Thick brush able liquid
- Coverage : 3 m2/kg/coat
- Optics: Opaque
Applications
- Petroleum industry
- Fertilizer industry
- Marine industry
How to use
-
Surfaces should be freed from laitance and dust by sand-blasting. In case sand-blasting is not possible, thorough abrading with a hard wire brush should be preferable. Suitable degreasing agent should be used to remove any grease, oil or traces on the surface.
-
Repair the surface if damaged. Allow 2-3 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Adhesives for repairing.
-
Apply primer for better adhesion on substrate. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Primers.
-
Mix the two components together thoroughly for at least 2 minutes so as to achieve uniform mixing and thorough consistency of the mix. Apply the mix using brush or spatula to the pretreated surfaces.
-
Allow 4-5 hours for surface to dry and 24 hours to achieve full strength.
MR. JO Protectokot- CRH
Packaging: 3.3 kg
Packaging: 6.65 kg
System Properties
- Color: Clear to pale yellowish
- Pot life @25°C: 20-25 mins
- Mixing Ratio: 100:33 PBW
- Resistant to concentrated acids
- Mixture consistency: Medium viscosity liquid
- Coverage : 4 m2/kg/coat
- Optics: Transparent/Translucent
Applications
- Chemical resistant coating
- Acid & chemical tank lining
- Interior lining of chimney
How to use
-
Surfaces should be freed from laitance and dust by sand-blasting. In case sand-blasting is not possible, thorough abrading with a hard wire brush should be preferable. Suitable degreasing agent should be used to remove any grease, oil or traces on the surface.
-
Repair the surface if damaged. Allow 2-3 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Adhesives for repairing.
-
Apply primer for better adhesion on substrate. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Primers.
-
Mix the two components together thoroughly for at least 2 minutes so as to achieve uniform mixing and thorough consistency of the mix. Apply the mix using brush or spatula to the pretreated surfaces.
-
Allow 4-5 hours for surface to dry and 24 hours to achieve full strength.
MR. JO Protectokot- CSA
Packaging: 6 KG
Packaging: 6 KG
System Properties
- Color: Pale yellow
- Pot life @25°C: 15-20 mins
- Mixing Ratio: 100:20 PBW
- Resistant to solvents, chemicals and inorganic acids
- Mixture consistency: Medium viscosity liquid
- Coverage : 4 m2/kg/coat
- Optics: Transparent/translucent
Applications
- Laboratories
- Distilleries
- Petrochemical industry
How to use
-
Surfaces should be freed from laitance and dust by sand-blasting. In case sand-blasting is not possible, thorough abrading with a hard wire brush should be preferable. Suitable degreasing agent should be used to remove any grease, oil or traces on the surface.
-
Repair the surface if damaged. Allow 2-3 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Adhesives for repairing.
-
Apply primer for better adhesion on substrate. Allow 4-5 hours for surface of repaired area to dry. Choose a suitable product from Jpoxy’s JO range of Primers.
-
Mix the two components together thoroughly for at least 2 minutes so as to achieve uniform mixing and thorough consistency of the mix. Apply the mix using brush or spatula to the pretreated surfaces.
-
Allow 4-5 hours for surface to dry and 24 hours to achieve full strength.